1967 Mustang Coupe 560's 1/8th mile

* 1967 Mustang coupe. All tube chassis (square main rails), NHRA certified March of this year tubular a-arms, ladder bar, braced 9in Ford with 4.88 pro gear, 35 spline Mark Williams axles, fiberglass hood, door, & decklid, body is excellent with no rust paint has normal racing wear & tear, stock dash with instrument cluster & factory pad, Lexan, 108� wheel base. This car hooks hard and runs as straight as you will ever see. Best et 5.65 with a 1.22 60'. 28,900 turn key Call Lance Brannon 256-443-6079
SPECS........
Short Block
 * Merlin II 526ci, 4.375 bore, 4.375 stroke
 * Callies Stealth crank
 * Oliver forged steel rods, 6.635" length, ARP/WSB
 * Venolia pistons, pin retainer buttons, 14:1 cr, Childs & Albert ZGS rings
 * 2nd set of Venolia pistons for 542" version
 * Crane roller cam,
 * Main studs, head studs
 * Jesel belt cam drive
 * MSD crank trigger, MSD billet distributer, MSD Pro Coil, Moroso Blue Max
 * Milodon wet sump, the good one (no pressure drops, 50# idle, 90# wide open)
Heads
 * Dart 360, intake port matched, valve pockets relieved
 * Jesel rocker shaft system, Jesel pushrods
 * Erson E915048 springs, inner of 3 springs removed, 320# seat pressure
 * Stainless valves, titanium retainers, lash caps
 * Springs and valve seals less than 30 passes
Intake
 * Dart intake, port matchedBG 1050
 * BG 1050 Dominator, BG 400 pump, BG fuel filter, BG 4-port regulator
 * #12 fuel cell to filter to pump, #10 pump to regulator, #8 regulator to carburetor
Transmission
 * Stock case and tail housing, this car has never cracked a case
 * TSI roller output shaft support
 * ATI standard front pump with hardened stator support
 * Front pump machined to accept needle bearing between clutch drum
 * ATI input shaft
 * 5 clutch high gear pack with steel clutch hub
 * low reverse clutch pack modified for lighter rotating mass
 * ATI dual ring servo piston
 * ATI Compuflow trans brake valve body and solenoid
 * TSI 1.80 straight cut planetary
 * Deep aluminum pan
Assembly Clearances
 * High gear .070
 * Low reverse .105
 * Rollerized end play .012 (oem stock is .035-.045)
 * Line pressure 180#
Torque Converter
 * ATI Treemaster
 * Flashes at 6200 rpm
Shifting
 * Husrt Quarter Stick
 * ACD chip control
 * CO2 (bottle lasts 250+ shifts, have spare bottle)
Electronics
 * MSD 2AL ignition, MSD Pro Coil, MSD crank trigger, MSD 2-Step
 * Dedenbear crossover delay box, Hurst line lock, both on for launch
 * ACD shift control
 * Auto Rod power control/fuse panel
 * Auto Gauge monster tach
 * Non battery wiring #14, battery connections wiring #1 AWG
 * Wiring junction with diagrams
 * 2 fresh 650 cca, 40 amp batteries
Aluminum
 * Firewall good condition
 * Driver and passenger floors new
 * Door panels new
 * Transmission tunnels new
 * Remaining aluminum to tail of body good condition
 * JAZ seat
Safety Harness
 * Simpson 5-point camlock
Dash
 * Stock dash metal skin
 * Stock original dashpad
 * Stock original instrument bezels
Gauges
 * Auto Gauge monster tach, oil pressure and engine temp

This item is USED

Trades NOT ACCEPTED

Payment options:

cash

Item Location: ROGERSVILLE, AL Get Directions

This ad expires in 21 days.